Adhesives

Bob Smith Industries

INSTA-SET CA Accelerator Pump Spray 2oz 151

MiG Ammo

Black CA Glue Slow Dry High Visibility 21g 8034

Flex-i-File

Touch-N-Flow Cement Applicator 711

Deluxe Materials

Roket UV Cement 5g AD88

DSPIAE Tools

Super Glue Auxiliary Applicator AT-GA

Bob Smith Industries

QUIK-CURE 5 Minute Epoxy 4.5oz 201

ABOUT QUIK-CURE™ 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE™ shouldn’t be used in areas that are subject to long-term...

Bob Smith Industries

INSTA-CURE Super Thin CA .5oz 101

ABOUT Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the...

Bob Smith Industries

MAXI-CURE Pocket CA Extra Thick w/ Pin In Cap .75oz 135

ABOUT Pocket CAs are available in 3/4 & 4 oz. sizes and feature a top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for...

Bob Smith Industries

PLASTIC-CURE Odorless Brush-On Gap Filling CA CA .5oz 105

ABOUT Plastic-Cure™ is a gap-filling formulation of CA that works best on plastics. It is packaged in a bottle with a brush built into its top, which in many cases is an easier way to apply the CA. As long as brush is put back into the bottle after use,...

Bob Smith Industries

INSTA-CURE+ Gap Filling CA .5oz 106

ABOUT Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface...

Bob Smith Industries

MAXI-CURE Extra Thick CA 1oz 112

ABOUT Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids. It can be carved...

Bob Smith Industries

INSTA-CURE+ Gap Filling CA 1oz 107

ABOUT Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface...

Bob Smith Industries

EXTRA CA OVERCAPS (Assorted Colors) (EACH)

Replacement colored cap that fits over the #312 top.

Bob Smith Industries

INSTA-CURE+ Pocket CA Extra Thick w/ Pin In Cap .75oz 133

ABOUT Pocket CAs are available in 3/4 & 4 oz. sizes and feature a top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for...

Bob Smith Industries

SUPER-GOLD+ Gap Filling Odorless Foam Safe CA .5oz 126

ABOUT SUPER-GOLD™ Thin and SUPER-GOLD+™ gap filling medium thickness are our odorless foam safe CAs. They are non-frosting and take only 2 or 3 seconds longer to bond compared to Insta-Cure and Insta-Cure+. There are no fumes that irritate the nose and...

Bob Smith Industries

MAXI-CURE Extra Thick CA .5oz 111

ABOUT Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids. It can be carved...

Bob Smith Industries

UN-CURE CA Debonder 1oz 161

ABOUT UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to...

Pacer

Z-Poxy 5 Minute 4oz PT37

Gator Glue

Gator's Grip Original Blend

Gator’s Grip Hobby Glue is known around the world as the go-to glue when working with photo-etch. Developed in 2005, Gator’s Grip was an attempt to find a solution to using cyroacnate glue, which has a very short working time and becomes brittle when dry...

Gator Glue

Gator's Grip Thin Blend

Gator’s Grip Hobby Glue is known around the world as the go-to glue when working with photo-etch. Developed in 2005, Gator’s Grip was an attempt to find a solution to using cyroacnate glue, which has a very short working time and becomes brittle when dry...

MiG Ammo

Activator for Cyanoacrylate Glue 8037

MiG Ammo

Acrylic Ultra Glue 40ml 2031

Woodland Scenics

Accent Glue 1.25oz 198

Accent Glue is applied to the base of Scenic Accents figures to adhere them to your layout (scuff up glue points with sandpaper before applying glue). Accent Glue allows for repositioning without applying more glue each time you move the figures.

Revell

Contacta Special Liquid Cement 30g 39606

Revell

Contacta Liquid Styrene Glue 39601

A typical plastic model adhesive works with the welding effect. This means that it dissolves the plastic and thus bonds the areas very firmly together. Revell Contacta Liquid is a super-thin liquid adhesive that is applied with a brush. The adhesive is...

Pacer

Zap 5 Minute Epoxy Quick Shot 1oz PT36

Pacer Technology’s Hobby product 5 Minute Quick Shot Epoxy (PT36) is a quick setting, fuel and vibration resistant formula that is durable and sandable in final cure. Perfect for on-the-spot field repairs.

Revell of Germany

Contacta Professional Liquid Cement w/Applicator 39604

Revell Contacta Professional for precise gluing. With the needle-fine cannula, micro-precise bonding can be carried out on tiny details and on the edges of transparent parts. Special properties: With plastic welding effect Liquid consistency of the...

GodHand Tools

GodHand Double Sided Tape 15mm for FF Board DST15

Double Stick Tape for FF Acrylic Board Double-Stick TapeWidth: 15 mmLength: 30 m

Army Painter

Miniature Plastic Glue (24ml) 2012

Also known as polystyrene cement, this special glue will mend and make attractive bonds between plastic parts of any miniature. Once dry, the miniature parts are fused together for a strong joint.

Army Painter

Miniature Super Glue (24 ml) GL2014

Also known as cyanoacrylate (CA) glue—this is super glue at its best. Medium thickness and high quality, this super glue is ideal for miniatures and small parts due to its precision tip. Creates a very strong bond between the parts being glued.

Army Painter

Battlefield Basing Glue GL2013

This is the glue needed when making your bases. Use with all Army Painter Tufts, Battleground basing, Battlefields flock and Rocks. 50ml. pot with pointy precision nozzle allowing for direct application and minimum waste. This glue completes the Army...

Woodland Scenics

Scenic Glue 8oz 190

A specially formulated, non-odorous adhesive for applying landscape materials. Scenic Glue is a thick, flexible, strong-hold adhesive that dries clear with a matte finish. Water-soluble and non-toxic. Apply Scenic Glue and press scenery material into...

Woodland Scenics

Hob-E-Tac Scenic Adhesive 2oz 195

Hob-e-Tac is a multi-purpose, water-soluble, high-tack adhesive. It is perfect for attaching Clump-Foliage™ to tree armatures. Also, use to glue Field Grass and Fine-Leaf Foliage™ to layout. 2 fl oz (59.1 mL)

Creative Dynamic

The Glue Looper Micro Applicator Tiny 103

 Single Shot Precision™ runs on capillary action, delivers only a fraction of the glue as the v2 Looper.- It uses a similar action to a quill pen, - Made for extreme control when gluing VERY small parts. It fits in any standard hobby knife handle...

Creative Dynamic

The Glue Looper Micro Applicator Thick 102

THE THICK LOOPER™ works like a quill pen. Using a proprietary loading technique, it draws a .015" line of glue placing it where you want it to go. Micro eddy currents combined with capillary action 'charge' the tool head with glue. This Looper was...

Plastruct

Plastic Weld Cement 002

Plastic Weld Cement is a clear, liquid plastic-bonding adhesive that will form bonds as strong as what's around it. If you need something to bond styrene, ABS or acrylics together this product should do the trick!

Testors

Liquid Plastic Cement 1oz 3502

Make sure your models stay strong with liquid plastic cement. Liquid Cement For Plastic is specially formulated for joining all polystyrene plastics. This product can be used in the construction of plastic model kits and may also repair many common...

Pacer

Slo-Zap 1oz PT20

Super Thick & Strong Use on high-stress areas. For laminating or forming fillets it's ideal. Position in 30 to 40 sec., cures in 90 sec.

Pacer

Zap CA Thin 1/2oz PT09

Super-thin penetrating formula. Works great on most materials, especially balsa and other soft woods. Excellent "wicking" action. Strengthens fiberglass cloth. Bonds in 1 to 5 seconds.

Pacer

Zap CA Thin 1/4oz PT10

Super-thin penetrating formula. Works great on most materials, especially Balsa and other soft woods. Excellent "wicking" action. Strengthens fiberglass cloth. Some uses besides hobbies and crafts include; jewelry manufacturing and repair, taxidermy,...

Testors

Wood Cement 5/8 oz

Instructions: Apply cement sparingly to one surface and press firmly together. Avoid cement on finger tips, as glue smudged on areas not to be joined cannot be removed. It will also discolor or cloud up clear parts. Do not use on clear parts.

Tamiya

Extra Thin Cement 40ml 87038

Tamiya EXTRA THIN model cement is used to glue together plastic model kits that use polystyrene plastic. No crevice is too small for this flowing adhesive, which was developed to flow into and stick the small spaces between two plastic parts which have...

Tamiya

Plastic Cement (Thick) 20ml 87012

This cement is for use in assembling plastic (styrene) models. It comes is a stable hexagonal bottle 47mm tall.Contents: 20ml.Features a brush for application on the reverse side of the cap.Working time between 1-2 minutes. Fully cures in 24 hours.

Pacer

Zap Medium Viscosity CA 1/4oz PT04

Superior gap filling formula.Medium viscosity.Allow approximately 7 to 10 seconds for part positioning.Average of 20 seconds for curing.Works on oily surfaces.Use zip kicker to accelerate cure time. Fills gaps. Works well on harder woods such as Bass and...

Tamiya

Thin Cement Quick 87182

Tamiya Extra Thin Cement is a widely popular glue among modelers around the world. You will find it in most modeler's workshops. This version is the quick setting variant that dries around 4 times faster than the original Tamiya Extra Thin Cement, saving...

Pacer

Zap Medium Viscosity CA 1/2oz PT03

  Medium viscosity formula.Cures clean and clear.Will not attack paint.Works on most plastic and vinyl.Non-flammable. Non-sniffable. Medium viscosity for plastics. Non-flammable. Cures clear. Won't attack paint. Great on most plastic models, car...

Woodland Scenics

Scenic Cement 16oz 191

Scenic Cement is a ready-to-use spray or brush-on adhesive specially formulated to glue Ballast, Turf and other landscape materials to a layout. This multi-use product is non-toxic, water-based and dries to a matte finish. Contains a wetting agent that...

Testors

Tube Cement 3501

Cement for plastic models is specially formulated for joining all polystyrene plastics. Cement for plastic models can be used in the construction of plastic model kits and may also repair many common household products made of polystyrene or ABS plastics.